manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 101 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 101

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (for example, cut or

wrongly connected pipe between sensor and throttle body or a hole in the intake manifold).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean.

Error for unexpected intake air in the rear cylinder manifold P0211

 - signal not valid.

Error cause

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is higher than the estimated one (for example, cut or

wrongly connected pipe between sensor and throttle body or a hole in the intake manifold).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean.

Estimation error for front cylinder intake manifold pressure P0215

 - pressure too high/pressure

too low.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean: there is an evident defect in the intake and pressure reading systems.

Estimation error for rear cylinder intake manifold pressure P0216

 - pressure too high/pressure too

low.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

SL 750 SHIVER

Electrical system

ELE SYS - 43

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments