manualshive.com logo in svg

APRILIA SCARABEO 50 I.E-100 4T - 2001, Workshop Manual, Page: 79 / 110

Share
Download
APRILIA SCARABEO 50 I.E-100 4T - 2001 Workshop Manual Download Page 79

Release 00

2003-02

78

Scarabeo 50 I.E.-50/100 4T

To check the fuse:

♦

Turn the ignition switch in the “ ” (OFF) position.

♦

Remove the inspection cover, see p. 22 (REMOVING
THE INSPECTION COVER).

♦

Remove the fuse (1) and inspect the filament (3). If it is
open, the fuse must be replaced.

♦

Replace the blown fuse with the spare fuse (4), or with
a new fuse having the same amperage rating.

If you replace the fuse and it blows again immedi-
ately, there is a serious problem with the electrical
system of your vehicle. Do not attempt to continue
using your vehicle. Take it to your Local aprilia
Dealer for repair and service.

NOTE

 

If you use the spare fuse (4), replace it as soon

as convenient.

FUSE CIRCUIT

A 7.5 amp fuse protects all of the electrical loads except
the lighting circuit, which is fed with alternating current
directly from the alternator.

WARNING

1

3

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001















































































































Reviews:

No comments