APRILIA SCARABEO 50 I.E-100 4T - 2001 Workshop Manual Download Page 46

Page: 46 / 110

Release 00

2003-02

Scarabeo 50 I.E.-50/100 4T

REMOVING THE COMPLETE DASHBOARD

Risk of fire.
Keep fuel and other flammable substances away from
the electrical components.

♦

Remove the front handlebar cover, see p. 26 (REMOV-
ING THE FRONT HANDLEBAR COVER).

♦

Unscrew and remove the two screws (1).

♦

Unscrew and remove the two screws (2).

Handle the plastic and painted components with care
and avoid scraping or damaging them.

Handle with care.
Do not force the electric cables.

♦

Partially remove the dashboard (3).

Support the dashboard, in order to prevent it from
accidentally falling down.

♦

Disconnect the speedometer/odometer cable (4) from
the dashboard.

♦

Disconnect the main connector (5).

♦

Remove the complete dashboard.

REMOVING THE DASHBOARD TRANSPARENT
SCREEN

♦

Remove the complete dashboard, see above (RE-
MOVING THE COMPLETE DASHBOARD).

Handle with care.
Upon disassembly and reassembly do not damage the
transparent screen and/or the couplings.

♦

Press on the four tabs (6) and remove the transparent
screen (7).

WARNING

CAUTION

100

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001















































































































Search results

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001

Reviews:

APRILIA SCARABEO 50 I.E-100 4T - 2001, Workshop Manual, Page: 46 / 110

Search results

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001

Reviews: