manualshive.com logo in svg

APRILIA SCARABEO 50 I.E-100 4T - 2001, Workshop Manual, Page: 30 / 110

Share
Download
APRILIA SCARABEO 50 I.E-100 4T - 2001 Workshop Manual Download Page 30

Release 00

2003-02

29

Scarabeo 50 I.E.-50/100 4T

4

4

11

6

5

8

7

9

REMOVING THE SADDLE SUPPORT 

Carefully read p. 2 (GENERAL SAFETY RULES).

♦

Remove the rear part of the fairing, see p. 22 (RE-
MOVING THE REAR PART OF THE FAIRING).

♦

Remove the battery as described on p. 75 (BATTERY
STORAGE).

♦

Detach the fuse strip (1) and the two dampers (2) and
(3) from their supports by passing them through the
slot as shown in the figure.

♦

★

Unscrew and remove the 4 screws (4).

♦

Unscrew and remove the filler cap (5).

♦

Remove the cap of the mixer oil tank (6).

♦

Disconnect the fuel breather pipe (7) from the fuel tank.

♦

Disconnect the drainage pipe (9) from the fuel bowl (8).

♦

Remove the fuel bowl (8).

NOTE

 

Disconnect the electric connection of the central

control unit.

♦

Pass the cabling, complete with relay switches and
fuse block through the slot in the front of the saddle
support.

♦

Lift the front section of the saddle support (11), slide it
frontward and remove it.

NOTE 

When reassembling the saddle support (11),

before positioning it in its seat, refit the fuel bowl (8)
correctly and connect it to the drainage pipe (9).

♦

Screw on the filler cap (5) and return the mixer oil tank
cap (6) to its correct position.

1

2

3

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001















































































































Reviews:

No comments