APRILIA SCARABEO 50 I.E-100 4T - 2001 Workshop Manual Download Page 28

Page: 28 / 110

Release 00

2003-02

Scarabeo 50 I.E.-50/100 4T

REMOVING THE REAR HANDLEBAR COVER

Carefully read p. 2 (GENERAL SAFETY RULES).

♦

Remove the front handlebar cover, see p. 26 (REMOV-
ING THE FRONT HANDLEBAR COVER).

♦

Disconnect the two electric connectors of the direction
indicators (1).

♦

Unscrew the metal ring (2) and withdraw the speedom-
eter / odometer cable (3) from the coupling.

♦

Unscrew and remove the three screws (4).

♦

Supporting the handlebar cover (5), disconnect the
connectors (6).

♦

Remove the rear handlebar cover (5).

REMOVING THE FRONT OUTER SHIELD

Carefully read p. 2 (GENERAL SAFETY RULES).

♦

Remove the complete fork, see p. 68 (REMOVING
THE COMPLETE FORK).

♦

Remove the front cover, see p.25 (REMOVING THE
FRONT COVER).

♦

Unscrew and remove the two screws (8).

♦

Remove the front outer shield (9).

100

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001















































































































Search results

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001

Reviews:

APRILIA SCARABEO 50 I.E-100 4T - 2001, Workshop Manual, Page: 28 / 110

Search results

Summary of Contents for SCARABEO 50 I.E-100 4T - 2001

Reviews: