manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 93 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 93

93

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

u

Start the engine, see page 69
(STARTING).

u

Release the throttle grip (4) (

Pos. C

).

With the engine idling, pull in the clutch
lever (5) completely.

u

Engage first gear, pushing the shift lever
(6) downwards.

u

Extend the side stand (1).

NOTE 

Extending the side stand must kill

the engine and the “side stand down”
warning light “

” (7) must come on. If the

engine continues to run:

u

Check the safety switch (3) on the side
stand (1), see page 93 (CHECKING
T H E   S W I T C H E S ) .   P e r f o r m   t h e
necessary cleaning or repairs.

u

Repeat the check.

WARNING

If the engine does not stop when the
side stand is extended, do not ride your
vehicle. Contact your Local 

aprilia

Dealer.

CHECKING THE SWITCHES

C a r e f u l l y   r e a d   p a g e 8 0
(MAINTENANCE).

Check the switches after the first 600 mi
(1,000 km) and thereafter every 4,650 mi
(7,500 km).

The vehicle is equipped with four switches:

– stoplight switch on the rear brake pedal

(1);

– stoplight switch on the front brake lever

(2);

– safety switch on the side stand (3);
– clutch lever switch (4).

u

Make sure that there is no dirt or mud on
the switch. The switch pin must move
freely and without interference, returning
automatically to its unapplied position.

u

Check the spring (5); it must not be
damaged, worn or stretched.

u

Make sure that the cables are connected
correctly.

1

5

5

2

3

4

APRum_RSV1000R##06_####.book  Page 93  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments