manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 88 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 88

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

88

AIR CLEANER

C a r e f u l l y   r e a d   p a g e 8 0
(MAINTENANCE).

WARNING

Do not use gasoline or flammable
solvents to wash the air cleaner, in
order to avoid fire or explosion.

CAUTION

Halve service intervals when the vehicle
is used in rainy or dusty conditions, on
rough roads or for racing.

Inspect the air cleaner to ensure that it has
not become clogged every 6,250 mi (1,000
km) or 12 months of use. Renew the air
cleaner every 12,500 mi (20,000 km). 

The air cleaner must be inspected more
frequently, cleaned if necessary, and
replaced more frequently if the vehicle is
used on dusty or wet roads. 

More frequent cleaning of the air cleaner is
suggested, especially if your bike is used
under very dusty conditions.

CAUTION

The air cleaner must not be used for
m o r e   t h a n   1 2 , 5 0 0   m i   ( 2 0 , 0 0 0   k m )
regardless of how many times it has
been cleaned in the interval. Under very
dusty or dirty conditions, it is advisable
to replace the air cleaner more often.

B e f o r e   t h e   c l e a n i n g   o p e r a t i o n ,   i t   i s
necessary to remove the air cleaner from

the vehicle.

KEEP POLLUTING SUBSTANCES AND
C O M P O N E N T S   A W A Y   F R O M
CHILDREN. DISPOSE OF POLLUTING
SUBSTANCES AND COMPONENTS
PROPERLY.

u

Every 6,250 mi (10,000 km) remove the
plug (1) so that any dirt that may have
accumulated inside the filter case can be
removed and disposed properly.

REMOVAL

u

Lift the fuel tank, see page 111 [LIFTING
THE FUEL TANK].

CAUTION

Before unscrewing and removing the
screws (2), clean the filter case cover (3)
and the filter case with a clean cloth.
Prevent any foreign matter from getting
into the inlet tubes. This could cause
severe engine damage.

u

Lift the fuel tank, see page 111 (LIFTING
THE FUEL TANK).

u

Release and remove the seven screws
(2).

u

Take off the air box cover (3).

u

Loosen and remove the two screws (4).

u

Remove the air cleaner retaining bracket
(5).

u

Extract the air cleaner (6).

u

Check the seal (7) for wear or damage
and replace as required.

1

2

2

2

2

2

2

2

APRum_RSV1000R##06_####.book  Page 88  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments