manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 52 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 52

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

52

DISC BRAKES

WARNING

As mentioned above, the brakes are the
most important safety system on your
vehicle. For your safety, they must be in
perfect condition, so they should be
checked every time you ride your
vehicle.

O i l   o r   o t h e r   f l u i d   o n   a   d i s c   w i l l
contaminate the brake pads. Dirty pads
must be discarded and replaced, a dirty
or oily disc must be cleaned with a high
quality degreaser.

Halve service intervals when the vehicle
is used in rainy or dusty conditions, on
rough roads or for racing.

Have your Local 

aprilia

 Dealer check

the levels of the brake fluid in the
reservoirs after the first 600 mi (1,000
km).

Arrange with your Local 

aprilia

 Dealer

to flush the systems and completely
change the brake fluid once every two
years.

NOTE 

This vehicle is fitted with front and

rear disk brakes. Each braking system is
operated by an independent hydraulic
circuit. 

The front brake is a twin-disk brake (one
disk on either side of the wheel).

The rear brake uses a single disk (fitted to
the right side of the wheel).

The information provided below applies to
both braking systems.

The brake fluid level decreases gradually
as the brake pads wear down. 

The front brake fluid reservoir is mounted
near the front brake lever coupling.

The rear brake fluid reservoir is positioned
under the right lower fairing; to reach it,
r e m o v e   t h e   r i g h t   l o w e r   f a i r i n g ,   s e e
p a g e 1 1 3   ( R E M O V I N G   T H E   S I D E
FAIRINGS).

NOTE 

Halve service intervals when the

vehicle is used in rainy or dusty conditions,
on rough roads or for racing.

Have the brake disks checked by an
Official 

aprilia 

dealer

 after the first 1,000

km (625 mi) and every 10,000 km (6,250
mi) afterwards.

Before each ride, check the brake fluid
level in both reservoirs - see page 53
(FRONT BRAKE) and page 54 (REAR
BRAKE), and check the brake pads for
wear - see page 99 (CHECKING THE
BRAKE PAD WEAR).

Have brake fluid changed every two years
by an Official 

aprilia 

dealer

.

WARNING

Never use your vehicle if any portion of
either brake system is leaking.

1

2

APRum_RSV1000R##06_####.book  Page 52  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments