manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 50 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 50

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

50

unlikely unless you handle used oil on a
daily basis, it is advisable to thoroughly
wash your hands with soap and water
after handling used oil.

KEEP OIL AWAY FROM CHILDREN.

DISPOSE OF OIL PROPERLY.

CAUTION

Be very careful not to spill oil when putting
oil in your vehicle. Clean up any spilled oil
mmediately because oil can damage the
finish of your vehicle. Also, oil on the tires
creates an extremely slippery and
therefore dangerous situation.

CAUTION

In case of oil leakage do not ride your
vehicle. Before using the vehicle, have it
repaired by your Contact your Local

aprilia 

Dealer.

ENGINE OIL

WARNING

If the engine oil pressure logo “

” (1)

remains on after the engine has started,
or if it comes on while you are riding
your vehicle, this means that the oil
system is not developing sufficient
pressure. In this case, immediately stop
the engine and Contact your Local 

april-

ia

 Dealer. Failure to heed this warning

can lead to engine seizure, upset, and
serious injury or even death.

CAUTION

Halve service intervals when the vehicle
is used in rainy or dusty conditions, on
rough roads or for racing.

Check the engine oil level every 300 mi
(500 km), see page 90 (CHECKING THE
ENGINE OIL LEVEL AND TOPPING UP) .

CAUTION

Have your Local 

aprilia

 Dealer change

the engine oil after the first 600 mi
(1,000 km), and thereafter every 4,650
mi (7,500 km) or every 2,300 mi (3,750
k m )   i f   y o u   u s e   y o u r   v e h i c l e   f o r
competition.

NOTE 

Use high-quality 15W – 50 oil,

see page 144 (LUBRICANT CHART).

APRum_RSV1000R##06_####.book  Page 50  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments