Home
/
APRILIA
/
RSV 1000 R FACTORY
/
Manual

APRILIA RSV 1000 R FACTORY, Manual, Page: 49 / 148

Share

Page: 49 / 148

APRILIA RSV 1000 R FACTORY Manual Download Page 49

49

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

USA

u

Lift the little cover (1).

u

Insert the key (2) in the cap lock (3).

u

Turn the key (2) clockwise, pull it and
open the fuel filler cap (4).

CAUTION

If you use a container or funnel for
refueling, make sure that it is perfectly
clean.
Any foreign matter getting into the fuel
tank may lead to severe damage.

WARNING

Do not add any additives or other
substances to the gasoline.

WARNING

Do not fill the tank completely. The fuel
should never be higher than the bottom
of the rim of the filler neck.

u

Refuel.

When you finish the refueling operation:

WARNING

After refueling, replace the fuel filler cap
(4) in the correct position.

NOTE

It is impossible to close the fuel

filler cap without the key.

u

With the key (2) inserted in the lock (3)
close the fuel filler cap (4) rotate the key
counterclockwise and push it.

u

Release the key (2). At this point the fuel
filler cap (4) is closed.

WARNING

Make sure that the fuel filler cap (4) is
properly closed.

u

Extract the key (2).

u

Close the little cover (1).

LUBRICANTS

WARNING

Proper vehicle lubrication is critical to safe
operation. Failure to maintain proper
lubricant levels or to use the proper type of
clean, new lubricant, can lead to an engine
or transmission seizure with subsequent
accident, serious injury or death.

WARNING

Use latex gloves for the maintenance
operations that require contact with used
oil. Used engine oil may cause skin cancer
if repeatedly left in contact with the skin for
prolonged periods. Although this is

APRum_RSV1000R##06_####.book Page 49 Monday, February 6, 2006 2:48 PM

«
...
47
48
49
50
51
...
»

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments