manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 33 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 33

33

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

Mu ltifunction
digital display 

Speedometer (km/h - MPH)

Can be set to display current, average or maximum road speed (in kilometers or miles) see page 34
(MULTIFUNCTION COMPUTER).To cycle through display readouts, see page 34 (MULTIFUNCTION
COMPUTER)

Odometer ( KM - Mi)

Gives total distance covered or distance covered since the trip meter was last reset (in km or miles).

Coolant temperature
(°C/°F)

Indicates the engine coolant temperature, see page 34 (MULTIFUNCTION COMPUTER). 

Do not leave the ignition switch in the "

" position, as this will stop the

cooling fans regardless of coolant temperature. Consequently, the

temperature will rise further.
When temperature rises up to the danger zone, stop the engine, turn the ignition key to "

" and wait

until the cooling fans switch off. 
Now turn the ignition key to "

" and check the coolant level, see page 60 (COOLANT).

Contact an Official 

aprilia 

dealer

.

Exceeding the maximum coolant temperature allowed (115 °C - 239
°F) may lead to severe engine damage.

Clock 

Displays the hours and minutes in accordance with the selected settings, see page 34
(MULTIFUNCTION COMPUTER).

Battery voltage
V BATT

Indicates battery voltage, see page 34 (MULTIFUNCTION COMPUTER).

Lap timer 

Indicates the various time measurements in accordance with the selected settings, see page 34
(MULTIFUNCTION COMPUTER).

Diagnostics

Each time the ignition switch is in the "

" position, the wording "

efi

" appears on the right side of the

multifunction display for approximately three seconds.

If the wording "

efi

" appears during normal engine operation, it

means that the Engine Control Unit has detected an anomaly.  In

most cases, the engine will keep running, but with reduced performance levels. Contact an
Official 

aprilia 

dealer

 immediately.

Description

Function

CAUTION

CAUTION

CAUTION

APRum_RSV1000R##06_####.book  Page 33  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments