manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 15 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 15

15

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

C.

No dealer is authorized to modify this

aprilia

 Limited Emission Control

System Warranty.

IV.

LEGAL RIGHTS.

 THIS WARRANTY

G I V E S   Y O U   S P E C I F I C   L E G A L
RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.

V. THIS WARRANTY IS IN ADDITION TO

THE 

aprilia

 LIMITED MOTORCYCLE

WARRANTY.

VI.

ADDITIONAL INFORMATION.

 Any

replacement part that is equivalent in
performance and durability may be
u s e d   i n   t h e   p e r f o r m a n c e   o f   a n y
maintenance or repairs. However,
aprilia is not liable for these parts. The
o w n e r   i s   r e s p o n s i b l e   f o r   t h e
p e r f o r m a n c e   o f   a l l   r e q u i r e d
maintenance. Such maintenance may
b e   p e r f o r m e d   a t   a   s e r v i c e
establishment or by any individual. The
warranty period begins on the date the
motorcycle is delivered to an ultimate
purchaser.

aprilia s.p.a.

Via G. Galilei, 1
30033 Noale (VE) Italy

aprilia USA, Inc.

140 E 45

th

 Street, 17C 

New York, NY 10012 

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments