manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 144 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 144

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

144

LUBRICANT CHART

Engine oil (recommended

):

 

 TEC 4T, SAE 15W - 50.

As an alternative to the recommended oils, it is possible to use high-quality oils with characteristics in compliance with or superior to the
CCMC G-4, A.P.I. SG. specifications

.

Fork oil type “R FACTORY”

: 

ÖHLINS 5W

Bearings and other lubrication points (recommended

):

 

 GREASE 30.

As an alternative to the recommended product, use high-quality grease for rolling bearings, working temperature range -30°C…+140°C,
dripping point 150 °C…230°C, high protection against corrosion, good resistance to water and oxidation

.

Protection of battery poles: 

Neutral grease or Vaseline.

Spray grease for chains (recommended): 

 CHAIN LUBE.

WARNING

Use new breake fluid only. Do not mix different makes or types of oil without having checked bases compatibility.

Brake fluid (recommended):

 

 BRAKE 5.1, DOT 4.

WARNING

Use new clutch fluid only.

Clutch fluid (recommended):

 

 BRAKE 5.1, DOT 4.

WARNING

Use only antifreeze and anticorrosive without nitrite, ensuring protection at -35 °C at least.

Engine coolant(recommended):

 

 

COOL.

APRum_RSV1000R##06_CAP08a01.FM  Page 144  Wednesday, September 27, 2006  2:01 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments