APRILIA RSV 1000 R FACTORY Manual Download Page 141

Page: 141 / 148

141

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

Saddles ..................................................................

Vehicle max. load
(rider+paluggage)....................................



414.5 lb (188 kg) -

427.3 lb (194 kg)

GEAR RATIOS

Ratio

Primary

Secondary

31/60 = 1 : 1.935

15/34 = 1 : 2.267

19/31 = 1 : 1.632

20/26 = 1 : 1.300

22/24 = 1 : 1.091

25/24 = 1 : 0.960

26/23 = 1 : 0.885

Final ratio

Total ratio

16/40 = 1 : 2.500

1:10.968
1:7.895
1:6.290
1:5.279
1:4.645
1:4.280

DRIVE CHAIN

Type .......................................................................

sealed, with no master link

Model .....................................................................

525

FUEL SUPPLY
SYSTEM

Type .......................................................................

electronic injection (Multipoint)

Choke.....................................................................

Ø 2.24 in (Ø 57 mm)

FUEL SUPPLY

Fuel ........................................................................

unleaded gasoline minimum octane rating (M+R)/2 method 90

FRAME

Type .......................................................................

Double beam frame, inclined, with light alloy cast elements

Rake.......................................................................

25°

Trail (with front tire 120/70) ....................................

4 in (101.7 mm)

SUSPENSIONS

Front.......................................................................

upside-down telescopic adjustable fork with hydraulic operation, fork leg Ø
1.69 in (Ø 43 mm)

Stroke.....................................................................

4.72 in (120 mm)

Rear .......................................................................

double-sided aluminium alloy swinging arm with progressive linkage and
APS syste m. Hydro -pneuma tic shoc k absorber with a djustable
compression/rebound/spring preload and length.

Wheel stroke ..........................................................

5.23 in (133 mm)

BRAKES

Front.......................................................................

with double floating disc brake Ø 12.60 in (Ø 320 mm); calipers with four
pins Ø 1.34 in (Ø 34 mm)

Rear .......................................................................

disc brake Ø 8.66 in (Ø 220 mm); caliper with double pin Ø 1.26 in (Ø 32
mm)

WHEEL RIMS

Type .......................................................................

light alloy with withdrawable pin

Front.......................................................................

17” x MT 3.50

Rear .......................................................................

17” x MT 6.00

APRum_RSV1000R##06_####.book Page 141 Monday, February 6, 2006 2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Search results

Summary of Contents for RSV 1000 R FACTORY

Reviews:

APRILIA RSV 1000 R FACTORY, Manual, Page: 141 / 148

Search results

Summary of Contents for RSV 1000 R FACTORY

Reviews: