manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 134 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 134

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

134

REPLACING THE FRONT AND 
REAR DIRECTION INDICATOR 
BULBS

Read page 131 (BULBS) carefully.

u

Place the vehicle on the stand, see page
77 (PLACING THE VEHICLE ON THE
STAND).

u

Unscrew and remove the screw (1).

CAUTION

The protective shield is retained by a
locating peg. Remove carefully or the
locating peg might break off.

u

Remove the lens (2).

CAUTION

On refitting, ensure that the lens fits
properly into its slot. Tighten the screw
(1) gradually. Do not overtighten or the
shield will damage.

u

Push down the bulb (3) gently and twist
counterclockwise.

u

Extract the bulb (3) from its seat.

CAUTION

When fitting the bulb, ensure that the
two locating pegs fit properly into the
slots in the bulb holder.

u

Install a new bulb of equal rating.

CAUTION

If the reflector (4) comes off its seat,
refit it correctly.

REPLACING THE LICENSE PLATE 
LIGHT BULB

Read page 131 (BULBS) carefully.

u

Place the vehicle on the stand, see page
77 (PLACING THE VEHICLE ON THE
STAND).

u

Remove the passenger saddle /
glove/tool kit compartment cover, see
page 45 (UNLOCKING/LOCKING THE
GLOVE/TOOL KIT COMPARTMENT
COVER).

1

2

1

4

3

APRum_RSV1000R##06_####.book  Page 134  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments