manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 133 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 133

133

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

CAUTION

Never pull on the wiring to disconnect a
bulb connector.

u

Disconnect the connector (4).

u

Rotate the lockring counterclockwise
and extract the bulb holder (5).

u

Fit a new bulb of equal rating.

u

Refit the bulb holder into the seat and
rotate clockwise to lock in place.

u

Refit the connector (4).

CAUTION

Never pull on the wiring to disconnect a
bulb connector.

PARKING LIGHT BULB

u

Remove the front fairing, see page 112
(REMOVING THE FRONT FAIRING).

CAUTION

Never pull on the wiring to extract a
bulb holder.

u

Grasp the parking light bulb holder (6)
and pull to extract.

u

Remove the bulb and fit a new bulb of
equal rating.

NOTE 

Ensure that the bulb fits correctly

into the bulb holder.

4

5

6

APRum_RSV1000R##06_####.book  Page 133  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments