manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 118 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 118

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

118

You must restore the circuit function by
connecting the wiring device (6) (

aprilia

part # 8124943), which is available at your

Local 

aprilia

 Dealer

, to the connector (5).

If the vehicle is used on closed course
competition, safety pegs (7) are available
for installation to the rider footrests to avoid
removal of the side stand.

WARNING

Removal of the safety pegs (7) fitted to
the rider footrests is only allowed after
removal of the side stand.

CAUTION

Never lean the vehicle against walls or
lay it on the ground. This could lead to
t h e   v e h i c l e   f a l l i n g   o v e r ,   c a u s i n g
damage to the vehicle and injury to
yourself or any other bystanders.
To park the vehicle without the stand
only the rear support stand 

 may be

used.

WARNING

Never disconnect or remove the safety
switch (4) without also removing the
stand. Disconnecting or removing the
safety switch (4) only makes it possible
to start the vehicle and ride off with
extended stand which may result in
upset, and serious injuries or even
death to the rider or bystanders, and
damage to the vehicle.

To remove the side stand:

u

Remove the left side cover, see
page 114 (REMOVING THE LOWER
FAIRINGS).

u

Lift the fuel tank, see page 111 (LIFTING
THE FUEL TANK).

NOTE 

Obtain a tie-wrap (7) to use for

reassembly.

CAUTION

Do  not force cables,  tubes, lines,
connectors and wires.

u

Cut the tie-wrap (8) and release the
cable (9).

u

Disconnect the electric connector (10)
from the connector (5).

6

5

10

9

7

APRum_RSV1000R##06_####.book  Page 118  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments