manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 116 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 116

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

116

WARNING

After reassembly, correctly adjust the
rearview mirrors and tighten the nuts in
such a way that the mirrors are secure.
Failure to heed this warning can prevent
you from seeing danger approaching
from behind and lead to a serious
accident.

After reassembly:

u

Correctly adjust the reflecting surface of
the rearview mirrors.

REMOVING THE FRONT BRAKE 
CALIPERS

WARNING

The disassembly and reassembly of the
front brake calipers can be difficult for
t h o s e   u n f a m i l i a r   w i t h   v e h i c l e
maintenance. You may wish to have
your Local 

aprilia

 Dealer carry out

these operations.
If you wish to perform these operations
y o u r s e l f ,   c a r e f u l l y   r e a d   p a g e 8 0
(MAINTENANCE).
The front brake system is equipped with
two separate calipers, one on the left
and one on the right side of the vehicle.
The following information may refer to
only one brake caliper but is applicable
t o   b o t h . W h i l e   d i s a s s e m b l i n g   a n d
reassembling the front brake calipers,
pay extra care not to damage the brake
lines, discs or pads.

NOTE 

You must use the appropriate

front 

 and rear 

 support stands to

remove the front brake calipers.

DISASSEMBLY

u

Place the vehicle on the appropriate
front support stand 

, see page 102

(PLACING THE VEHICLE ON THE
FRONT SUPPORT STAND 

).

WARNING

Make sure that the vehicle is stable. 
If it falls over, it may cause damage to
bystanders and other property, as well
as be damaged itself.

u

Rotate the wheel manually, so that the
space between two spokes of the rims
lines up with the brake caliper.

u

Have a helper steady the handlebar in
the straight ahead position.

Brake caliper screw (1) tightening
torque: 36.16 ftlb (50 Nm).

1

APRum_RSV1000R##06_####.book  Page 116  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments