APRILIA RSV 1000 R FACTORY Manual Download Page 112

Page: 112 / 148

use and maintenance

RSV 1000 R

- RSV 1000 RFACT

USA

112

Always ensure that the fuel filler cap is
correctly closed.

Remove the rider saddle, see page 111
(REMOVING THE RIDER SADDLE).

Remove the side panels, see page 114
(REMOVING THE LOWER FAIRINGS).

Unscrew and remove the two retaining
screws (4) at the front end of the fuel
tank (5).

Raise the fuel tank (5) at the front using
a suitable support to hold it up.

REMOVING THE FRONT FAIRING

Remove the rearview mirrors, see page
115 (REMOVING THE REARVIEW
MIRRORS)

Place the vehicle on the stand, see page
77 (PLACING THE VEHICLE ON THE
STAND).

Turn the ignition switch to "



Remove the rearview mirrors, see page
115 (REMOVING THE FAIRING UPPER
FRONT COVERS).

Release the four plastic rivets (1) using a
flat-blade screwdriver.

Release and remove the screw (2) in the
centre.

CAUTION

Do not overtighten the screw (2) on
refitting, as it sits on plastic.

u H

Release and remove the snap-on
fasteners (3) securing the front fairing
to the side fairings.

APRum_RSV1000R##06_####.book Page 112 Monday, February 6, 2006 2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Search results

Summary of Contents for RSV 1000 R FACTORY

Reviews:

APRILIA RSV 1000 R FACTORY, Manual, Page: 112 / 148

Search results

Summary of Contents for RSV 1000 R FACTORY

Reviews: