manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 103 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 103

103

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

Riding with damaged rims in dangerous
for the rider, the vehicle and other people.
Check the conditions of the rim and have
it replaced if it is damaged.

WARNING

Have the rim replaced by your Local

a p r i l i a

 Dealer. You mu st  use the

appropriate front and rear support stands
(1) (2) to remove the front wheel.
DISASSEMBLY

u

Remove the left and right front brake
caliper (3), see page 116 (REMOVING
THE FRONT BRAKE CALIPERS).

CAUTION

Never touch the front brake lever after
removing the brake calipers from the
discs. If you do, the caliper pistons may
be pushed out of their seats, and brake
fluid will be spilled. 

Should you accidentally do this, take
your vehicle to your Local 

aprilia

Dealer who will know how to repair this
damage.

u

Place a support (4) under the front tire, in
such a way as to keep the wheel in its
position after loosening it.

WARNING

Make sure that the vehicle is stable. 
If it falls over, it may cause damage to
bystanders and other property, as well
as being damaged itself.

u

Have a helper steady the handlebar in
the straight ahead position.

Wheel nut (5) tightening torque: 
57.86 ftlb (80 Nm).

u

Remove the wheel nut (5) and washer
(6).

Axle clamp screw (7) (8) tightening
torque: 8.7 ftlb (12 Nm).

u

Loosen the two axle clamp screws (7)
(right side), using the appropriate Allen
wrench.

u

Loosen the two axle clamp screws (8)
(left side), using the appropriate Allen
wrench.

NOTE 

Observe the arrangement of the

right spacer ring (9), in order to be able to
reassemble it correctly.

NOTE 

To facilitate the extraction of the

axle (10), slightly lift the wheel.

u

Push the axle (10) partly out of the front
fork by tapping the threaded end with a
rubber hammer or wooden drift.

u

Support the front wheel and remove the
axle (10) manually by pulling it from the
left side of the vehicle.

u

Remove the wheel by pulling it forward.

6

5

10

7

8

APRum_RSV1000R##06_####.book  Page 103  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments