manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 102 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 102

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

102

u

Rest one foot on the rear part of the
stand (8).

u

Push the stand (8) downwards until it
reaches the end of its stroke (see figure).

WARNING

Make sure that the vehicle is stable. 
If it falls over, it may cause damage to
bystanders and other property, as well
as being damaged itself.

PLACING THE VEHICLE ON THE 
FRONT SUPPORT STAND 

u

Place the vehicle on the appropriate rear
s u p p o r t   s t a n d  

,   s e e  p a g e 1 0 1

(PLACING THE VEHICLE ON THE
REAR SUPPORT STAND) 

.

u

Lift the front part of the stand (8) and
insert each of its ends (9) into holes (10)
in the bottom of the front fork.

u

Rest one foot on the front part of the
stand (8).

u

Push the stand (8) downwards until it
reaches the end of its stroke (see figure).

WARNING

Make sure that the vehicle is stable. 
If it falls over, it may cause damage to
bystanders and other property, as well
as being damaged itself.

FRONT WHEEL

WARNING

The disassembly and reassembly of the
front wheel can be difficult for those
unfamiliar with vehicle maintenance.
You may wish to have your Local 

april-

ia

 Dealer carry out these operations.

If you wish to perform these operations
y o u r s e l f ,   c a r e f u l l y   r e a d   p a g e 8 0
(MAINTENANCE).

While disassembling and reassembling
the wheel, pay extra care not to damage
the brake lines, discs or pads.

B ef ore  c arry ing ou t t he  f ollow ing
operations, let the engine and the
exhaust silencer cool down until they
reach room temperature. 
Failure to observe this warning can lead
to serious burns.

8

10

9

4

1

2

3

APRum_RSV1000R##06_####.book  Page 102  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments