manualshive.com logo in svg

APRILIA RSV 1000 R FACTORY, Manual, Page: 101 / 148

Share
Download
APRILIA RSV 1000 R FACTORY Manual Download Page 101

101

use and maintenance  

RSV 1000 R 

- RSV 1000 RFACT 

USA

USA

ASSEMBLING THE PINS FOR THE 
REAR SUPPORT STAND 

u

Place the vehicle on the stand, see
page 77 (PLACING THE VEHICLE ON
THE STAND).

u H

Place the pin (1) on the appropriate
seat on the swinging arm.

u H

Insert and tighten the screw (2) in the
appropriate threaded hole (3) in the
swinging arm.

PLACING THE VEHICLE ON THE 
REAR SUPPORT STAND 

u

Assemble the pins for the rear support
stand 

, see above (ASSEMBLING

THE PINS FOR THE REAR SUPPORT
STAND ).

NOTE 

Have someone help you keep the

vehicle vertical with the two wheels on the
ground.

u H

Slacken the knob (7).

u H

Shift the fork-shaped support (6) so
that its width matches the distance
between the two pins (1) fitted to the
swinging arm.

u H

Tighten the knob (7).

u

Slide both fork-shaped seats (6) of the
stand (8) underneath the pins (1) fitted to
the vehicle simultaneously.

u

Place one foot on the rear end of the
stand (8).

u

Push down on the stand (8).

CAUTION

Make sure the vehicle is stable.

1

3

2

1

5

1

5

1

8

6

7

APRum_RSV1000R##06_####.book  Page 101  Monday, February 6, 2006  2:48 PM

Summary of Contents for RSV 1000 R FACTORY





















































































































































Reviews:

No comments