manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 81 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 81

•

Unscrew and remove the cap to drain

out the engine oil.

•

Unscrew and remove the engine oil fil-

ter.

•

Fit a new engine oil filter.

•

Add engine oil up to the correct level.

•

Start the engine, wait some seconds,

then stop the engine and check the oil

level again. Top up and set the level if

necessary.

Air filter

•

Remove the fuel tank.

•

Unscrew and remove the ten screws.

•

Remove the filter box cover.

COVER THE INTAKE DUCTS WITH A CLEAN CLOTH TO
PREVENT FOREIGN BODIES FROM ENTERING THE IN-
TAKE DUCTS. UPON REFITTING, BEFORE REPLACING
THE FILTER CASE COVER , MAKE SURE THAT THE
CLOTH OR OTHER OBJECTS ARE NOT LEFT INSIDE.
MAKE SURE THAT THE FILTER ELEMENT IS CORRECTLY
POSITIONED, SO NO UNFILTERED AIR CAN PASS. DO
NOT FORGET THAT THE EARLY USE OF THE PISTON AND
CYLINDER SEGMENTS CAN BE CAUSED BY A FAULTY
OR MISPLACED FILTER ELEMENT.

•

Unscrew and remove the four screws.

•

Remove the air-box cover.

•

Remove the filtering element.

Caponord 1200 - Caponord 1200 Rally

Maintenance

MAIN - 81

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments