manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 552 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 552

Carry out the listed checks before delivering the motorcycle.

WARNING

HANDLE FUEL WITH CARE.

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

- Dirt

Tightening torques inspection

- Safety fasteners:

front and rear suspension unit

front and rear brake calliper retainer unit

front and rear wheel unit

engine - chassis retainers

steering assembly

- Plastic parts fixing screws

Electrical system

- Main switch

- Headlamps: high beam lights, low beam lights, tail lights (front and rear) and their warning lights

- Headlight adjustment according to regulations in force

- Front and rear stop light switches and their bulbs

- Turn indicators and their warning lights

- Instrument panel lights

- Instrument panel: fuel and temperature indicator (if present)

- Instrument panel warning lights

- Horn

- Electric starter

- Engine stop via emergency stop switch and side stand

- Helmet compartment electrical opening switch (if present)

Pre-delivery

Caponord 1200 - Caponord 1200 Rally

PRE DE - 552

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments