manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 468 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 468

•

Retrieve the tone wheel (2).

•

Then retrieve the brake disc (3).

Front brake disc

Removal

REMOVAL OF FRONT LEFT DISC BRAKE

•

Carry out the removal of the front

wheel.

•

Undo and remove the six fixing screws

(1).

•

Remove the brake disc (2).

REMOVAL OF RIGHT FRONT BRAKE

•

Carry out the removal of the front

wheel.

•

Unscrew and remove the three fixing

screws (1) of the tone wheel (2).

Braking system

Caponord 1200 - Caponord 1200 Rally

BRAK SYS - 468

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments