manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 433 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 433

•

Working from the left side, unscrew

and remove the nut and collect the

washer.

REMOVAL SHOULD BE CARRIED OUT WITH UTMOST
CAUTION.
SUPPORT THE SWINGARM FROM THE FRONT TO AVOID
ACCIDENTAL FALLS.
PLACE A WOODEN SUPPORT UNDER THE FRONT PART
OF THE REAR SWINGARM TO PREVENT IT FROM LOW-
ERING AND TO KEEP IT UPRIGHT.

•

Working on the right side, unscrew and

remove the swingarm bolt.

UPON REMOVING THE REAR SWINGARM PAY ATTEN-
TION NOT TO JAM THE GEARING CHAIN.

See also

Removing the

rear wheel

Drive chain

Removing

The transmission chain, although "closed", has a

different coloured hammerlock (where provided),

which should be used to perform opening / disas-

sembling procedures.

NOTE

WHERE PRESENT, THE HAMMERLOCK (1) MAY ALSO BE
IDENTIFIED BY A SIGN (2) APPLIED IN THE MOUNTING
LINES DURING MANUFACTURING.

Caponord 1200 - Caponord 1200 Rally

Chassis

CHAS - 433

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments