manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 309 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 309

•

Collect the special shim featuring two

thicknesses.

Checking the clutch plates

•

Lay the friction discs and steel discs on

a level surface and check them for

cracks and potential distortions.

Maximum distortion allowed: 0.20 mm (0.0079

in)

•

Measure the driving plate thickness at

four positions, replace them all if not

complying with specifications.

CAUTION

THE STEEL DISCS MUST SHOW NO SCORES OR TEM-
PERING COLOUR.

•

Measure the thickness of the clutch

plates at four positions, replace them if

not complying with specifications.

Minimum thickness of the eleven driving

plates (individually): 2.75 mm (0.11 in).

Minimum thickness of the ten driven plates (in-

dividually): 2,75 - 2,85 mm (0.108 ÷ 0.112 in).

MUSHROOM VALVE CHECK

•

Check if the valve slides freely, without

jamming.

•

Blow compressed air into the valve and

check that the lubricating oil passage

holes open.

Caponord 1200 - Caponord 1200 Rally

Engine

ENG - 309

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments