manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 227 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 227

Pin out:

1 blue/green cable: ground connection

2 yellow/red cable: 5 V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: STATUSES

RUN / STOP switch

•

Run/Stop

NOTES

•

Indication on the diagnostics instrument always on STOP: disconnect the connector and,

with the switch set to RUN, check if there is continuity towards the two cables switch - Blue/

Green and Yellow/Red: If there is not continuity, replace the sensor; if there is continuity,

check the connector: if not OK, restore the cable harness; if OK, check, with key set to ON,

if there is voltage on Yellow/Red cable: if there is no voltage, restore the cable harness; if

there is, check the Yellow/Red cable ground insulation: If there is continuity with ground

connection, restore the cable harness; if OK, set the key to OFF and check the VEHICLE

connector and the engine-vehicle cable harness connector: if it is not OK, restore; if it is OK,

check the continuity of the Yellow/Red cable between the switch connector and VEHICLE

connector PIN 78: if not OK, restore the cable harness; if OK, replace the Marelli control

unit.

•

Indication on the diagnostics instrument always on RUN: disconnect the connector and, with

the switch set to STOP, check if there is continuity between the two cables of the switch: if

there is continuity, replace the switch; otherwise, it means that, with key set to ON, the

Yellow/Red cable (between switch and the PIN 78 of the control unit connector) is shorted

to positive: restore the cable harness.

Butterfly valve in exhaust

Function

Optimises engine operation at low revs without

compromising the efficiency of the exhaust system

at high revs.

Operation / Operating principle

The system consists of a throttle valve with a re-

turn spring placed on the exhaust pipe. The valve

is closed by means of two cables moved by an

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 227

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments