manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 193 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 193

Air temperature sensor

Function

it tells the control unit the intake air temperature in

order to calculate oxygen presence so as to opti-

mise the petrol quantity necessary for correct com-

bustion

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature)

Level in wiring diagram:

Temperature sensors

Location:

•

sensor: on filter box left side, next to

rear throttle body

•

connector: on the sensor

Electrical characteristics:

Resistance

•

at 0 °C (32 °F): 32.5 k

Ω

 ± 5%

•

at 25 °C (77 °F): 10.0 k

Ω

 ± 5%

Pin out:

1. 0-5 V signal

2. Ground connection

DIAGNOSIS INSTRUMENT:

 

PARAMETERS

Air temperature

Example value with key ON: 45 °C (113 °F)

In case of recovery, this value is set by the control

unit

Air temperature pre Recovery

Example value with key ON: -40 °C (-40.0 °F)

Value drawn from the signal read without taking

into account any recovery: the value in the exam-

ple refers to an open circuit

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

air temperature sensor P0110

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 193

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments