manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual, Page: 173 / 573

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 173

Battery

Function

Battery YTX 14-BS, which must be activated and

loaded.

Level in electrical circuit diagram:

Battery recharge

Location:

•

on the vehicle: under the saddle

•

connector: on the battery

Electrical specifications: 12

 Ah

Pin out:

1. Positive pole (red): approx. 12.6 V

2. negative pole (black): ground connection

DIAGNOSTICS INSTRUMENT:PARAMETERS

Battery voltage

•

Example value with key ON: 12.0 V

•

Example value with engine on: 14.2 V

In case of recovery, this value is set by the control

unit

Battery voltage pre Recovery

•

Example value with key ON: 12.0 V

•

Example value with engine on: 14.2 V

Value drawn from the signal read without taking

into account any recovery

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Battery voltage P0560

•

too high/too low

Error cause

•

If too high: too high a voltage has been detected at PIN 42. If too low: too low a voltage has

been detected at PIN 42. The instrument panel does not indicate the presence of this error

even in the ATT status.

Troubleshooting

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 173

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments