APRILIA 854239 Service Station Manual Download Page 90

Page: 90 / 216

•

Remove the gear locking pawl and re-

trieve the washer and the spring.

See also

Disassembling the

clutch

Splitting the

crankcase halves

Checking the gear selector

Check the stop lever for damage and wear and make sure the ball rotates freely.

If necessary, replace the parts.

Check the gear selector spring for damage and wear.

If necessary, replace the part.

Check the selector shaft and its teeth for damage and wear.

If necessary, replace the part.

Check the lever spring for damage and wear.

If necessary, replace the part.

•

Check the clearance of the washer and the riveted pin that passes through the plate. If it is

excessive, replace the pawl.

Reassembling the gear selector

•

To refit, lubricate and carry out the removal operations but in reverse order.

Generator side

Engine

MXV 450

ENG - 90

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands