APRILIA 854239 Service Station Manual Download Page 205

Page: 205 / 216

Coolant replacement

•

Place a container of suitable capacity

underneath the sleeve.

•

Release the clamp.

•

Slide off the sleeve.

•

Empty the liquid into the container.

•

Open the radiator cap to facilitate

drainage.

FILLING

•

Refit the sleeve and fasten it with a new clamp.

•

Top-up with coolant.

See also

Top-up

Water pump

CAUTION

IT IS NOT NECESSARY TO REMOVE THE COOLANT PUMP UNLESS THE COOLANT LEVEL IS
EXTREMELY LOW OR WHEN THE COOLANT DOES NOT HAVE ENGINE OIL.

NOTE

PLACE A CLOTH UNDER THE PUMP BEFORE REMOVING ITS COMPONENTS.

•

Undo and remove the four pump cover

fixing screws.

•

Remove the water pump cover and col-

lect the seal gasket.

MXV 450

Cooling system

COOL SYS - 205

Summary of Contents for 854239

























































































































































































































Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands

APRILIA 854239, Service Station Manual

Search results

Summary of Contents for 854239

Reviews:

Related manuals for 854239

Brands by name

Popular brands