APRILIA 854239 Service Station Manual Download Page 193 | Manualshive

Page: 193 / 216

background image

•

Undo and remove the screw (1).

•

Release the spring (2).

•

Remove the rear brake pedal (3).

•

Unscrew and remove the swingarm pin

fixing nut.

•

Remove the swingarm pin.

Drive chain

This vehicle is equipped with a chain

without O-rings

and with master link.

EXCESSIVE CHAIN SLACKENING MAY CAUSE IT TO COME OFF THE PINION OR THE CROWN,
WHICH IN TURN COULD CAUSE AN ACCIDENT OR SERIOUSLY DAMAGE THE VEHICLE.
CHECK THE CHAIN SLACK ON A REGULAR BASIS AND ADJUST IT AS NECESSARY. TO
CHANGE THE CHAIN TAKE YOUR VEHICLE TO AN Official aprilia Dealer, WHO WILL PROVIDE
ACCURATE, PROMPT SERVICE.

CAUTION

MXV 450

Chassis

CHAS - 193

«
...
191
192
193
194
195
...
»

Summary of Contents for 854239

























































































































































































































Reviews:

No comments

Related manuals for 854239

Brand: Honda Pages: 104

Brand: Avenger Pages: 31

Brand: KTM Pages: 22

Brand: oset Pages: 44

Brand: ESAB Pages: 4

GRIZZLY 90 2020

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 452

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 116

Brand: DYNATEK Pages: 6

Brand: G PLAST Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands