Apricus AP250GLE Installation Manual Download Page 10

                          Issue Date: 01.06.16 

 

     

   Review Date: 01.06.16  

H0024 028626 A  

Installation Manual for EHW Tanks: MAN_INST_TANK_SRT(AA)|10

 

 

Figure 3 Apricus Pump Station Kit 

5.3.1.3 SOLAR RETURN 

IMPORTANT 

Cap  this  port  with  brass  plugs  supplied  when  solar 
collectors are not being installed. 

 
When solar DHW system is set up, this port is used for the 
water line returning from the solar collectors after being 
heated.  This  line  does  not  require  any  additional 
components, but should be run as short as possible and 
have continuous fall back to the solar return port. 

Apricus  recommends  using  a  three  way  ball  valve  and 
drain on the solar return line to allow convenient system 
filling and draining.  

On  the  solar  return  line  near  the  tank  port,  it  is 
recommended  to include a U-shaped heat trap  with an 
approximate  25cm  dip  in  the  piping  configuration  to 
prevent reverse thermos-siphoning. 

5.3.1.4 OUTLET 
The  outlet  is  where  the  hot  water  from  the  tank  is 
extracted to be supplied to the household.  

5.3.1.5 SENSOR PORTS 
When solar DHW system is set up, the sensors must be 
coated with heat transfer paste and inserted through the 
cable  gland  into  the  appropriate  sensor  port  and 
tightened. The top sensor port houses S3 and the bottom 
sensor port houses S2. 

The  Apricus  controller  requires  three  sensor  leads  be 
installed  into  the  appropriate  sensor  ports  in  the  solar 
system; this is vital for operation of the solar system.  

The first temperature sensor port is located on either side 
of  the  collector  manifold.  Sensor  1  (S1)  must  be 
connected to the outlet of the manifold (the higher side). 
Apricus  solar  rated  tanks  come  with  two  temperature 
sensor ports. The bottom port connects to the Sensor 2 
(S2), the top port connects to the Sensor 3 (S3) sensor. 

5.3.1.6 PTRV PORT 
The  PTRV  port  is  where  the  tank  ‘pressure  and 
temperature  relief  valve’  is  to  be  installed.  All  PTRV’s 
must  be  fitted  with  a  copper  drain  pipe  to  carry  any 
discharge to an appropriate drain. 

IMPORTANT 

All storage tanks include a PTRV, which is located  in 
the tank packaging, either in a box, vertical column or 
element cover. 

 

Summary of Contents for AP250GLE

















Reviews: