manualshive.com logo in svg

Applied Biosystems QuantStudio 6 Flex, User Manual

Share
Download
Applied Biosystems QuantStudio 6 Flex User Manual Download Page 45

Note: 

Before starting the calibration, the instrument may pause (up to

10 minutes) to allow the heated cover to reach the required temperature.

8.

When the run is complete and the software displays the Analysis screen, select

each filter from the Filter Set drop-down list, then confirm that the

corresponding ROI Image displays a green circle around each well area.

9.

After you inspect all ROI images, confirm the status of the calibration, where

passed indicates that the run produced viable calibration data, and failed indicates

that the run did not produce data or that the data it collected is unusable.

Analysis status

Action

Passed

Click Next.

Failed

Troubleshoot the failed calibration (see “Troubleshooting“).

10.

Unload the calibration plate or array card:

a.

After the calibration, tap   on the touchscreen to eject the plate or array

card.

Note: 

If the instrument does not eject the plate or array card, remove it as

explained in “Troubleshooting“.

b.

Remove the ROI calibration plate or array card from the instrument tray and

store it in the dark at room temperature until you are ready to perform the

uniformity calibration.

WARNING! 

PHYSICAL INJURY HAZARD. During instrument

operation, the plate or array card temperature can reach 100°C. Allow

the consumable to cool to room temperature before removing.

c.

Tap   on the instrument touchscreen to close the instrument tray.

11.

In the ROI Calibration screen, click Finish to complete the calibration, then click

Yes when prompted to save the results.

Note: 

If the QuantStudio

™

 Real-Time PCR Software displays the warning

Saving ROI calibration will invalidate other existing calibrations except HRM

Calibrations, click OK to proceed.

Note: 

HRM (High Resolution Melt) is a separately licensed module. If your

instrument requires this module, contact Thermo Fisher Scientific.

12.

(Optional) Click Print Report in the upper right corner of the screen to print a

summary of the calibration results for your records.

Background calibration

The software uses the background calibration data during subsequent experiments to

remove background fluorescence from the experiment data.

Chapter 2 

Calibrate the instrument

Background calibration

2

QuantStudio

™

 6 and 7 Flex Real-Time PCR Systems v1.6 Maintenance and Administration Guide

45

Summary of Contents for QuantStudio 6 Flex



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands