Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 52

Page: 52 / 132

3-24 Instrument Setup

If the PCMCIA Flash Memory Card contains a valid firmware upgrade, the

Upgrade

screen appears.

If successful, the

Firmware Upgrade Successful

screen displays the firmware

version to which you have upgraded.

Pressing the

Run

key in the lower right corner brings up the

Main

menu with the new

revision number of the software listed on the screen.

Remove the PCMCIA Flash Memory Card after you have successfully upgraded the
firmware.

To upgrade using a PCMCIA Flash Memory Card:

(continued)

Step

Action

DO NOT TURN OFF THE INSTRUMENT

OR REMOVE THE PC CARD!

Upgrading the instrument firmware

will take approximately 30 seconds.

Instrument will re-boot when complete.

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands