Applied Biosystems 7300 Installation And Maintenance Manual Download Page 94

Page: 94 / 174

Chapter 6

Performing the Pure Dye Calibration

Overview

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Overview

Note:

You can also use the Real-Time System Setup wizard

to perform the procedure in

this chapter. To access the wizard, select

Program Files 7300/7500/7500

Fast System

Real-Time System Setup Wizard

Time Required

•

7300 systems:

45 minutes

•

7500/7500 Fast systems:

1 hour

Materials

Required

When to Perform

Pure Dye

Calibrations

Perform a pure dye calibration:

• When installing the system (you must perform all calibrations in this order: ROI

background optical (7500/7500 Fast systems only) pure dye instrument
verification).

• Every 6 months, depending on instrument use.

IMPORTANT!

You must perform a background run before every pure dye calibration.

Because the age and use of instrument components can affect pure spectra readings,

Applied Biosystems recommends performing a pure dye calibration at least every six

months.

Safety

Glasses

Powder-free

Gloves

Pure Dye Plates

(FAM

™

, JOE

™

, NED

™

ROX

™

, SYBR

Green,

TAMRA,

™

and VIC

dyes)

Pure Dye Plates

(CY3, CY5, and

TEXAS RED

dyes)

7300, 7500/7500

Fast system

7500/7500 Fast

system only

Applied Biosystems

Real-Time PCR System

Spectral Calibration Kit

GR2170

Centrifuge with plate

adapter

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands