Applied Biosystems 7300 Installation And Maintenance Manual Download Page 166

Page: 166 / 174

Appendix D

Connecting to the Network and Downloading Adobe Acrobat

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

140

Notes

Connecting to the Network and Downloading Adobe Acrobat

Connect your computer to the network. For help in connecting your computer to the
network, see your system administrator.

IMPORTANT!

Do not use the 7300/7500/7500 Fast System on a wireless network.

Use of a wireless network can interfere with data collection and may result in

data loss.

Download Adobe

Acrobat

Reader (free shareware) from www.adobe.com. Note

that you must download Adobe

Acrobat

Reader to view document links

referenced in the Real-Time System Setup wizard and the Sequence Detection
Systems Online Help.

After the computer is set up, proceed with the installation by using either:

• The Real-Time System Setup wizard provided on the Installation CD (which

starts automatically after a slight delay when you insert the CD in to the CD
drive of the computer,

• This installation and maintenance guide.

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands