manualshive.com logo in svg

Applent Instruments AT824, User Manual, Page: 45 / 52

Share
Download
Applent Instruments AT824 User Manual Download Page 45

 

45 

Remote Control 

8.4.8

 

SYST System Sub System 

 

SYST:KEYL <ON | OFF | 1 | 0> 

 

To lock/unlock keypad and touch screen 

sHeader 

SYST:KEYL 

sPara 

<ON | OFF | 1 | 0> 

 

Tips: 

When the keypad and screen is locked, press[ ]to unlock

！

 

Power key cannot be locked 

 

 

SYST:HOLD <ON | OFF | 1 | 0> 

 

To hold data on the screen 

sHeader 

SYST:HOLD 

sPara 

<ON | OFF | 1 | 0> 

 

Tips: 

When the screen is data hold, a red sign 

DH

 will be displayed 

on screen. 

This command is only available on <MEAS DISPLAY> page. 

8.4.9

 

IDN? Subsystem 

 

IDN? 

 

To check version information   

sHeader 

IDN? 

sPara 

 

Response 

AT826,REV A1.0,<Serial Number>,Applent Instruments Inc. 

8.4.10

 

RST Subsystem 

 

RST 

 

To start in heat 

sHeader 

RST 

sPara 

 

8.4.11

 

  Error Subsystem   

 

ERR? 

 

To check the message sent previously 

sHeader 

ERR? 

sPara 

 

Response 

In the following Table 

Table 8-5 The Error Code and message 

0, No error 

 

1, Bad command 

Summary of Contents for AT824





















































Reviews:

No comments