Apogee Caliper Instructions Manual Download Page 1 | Manualshive

Page: 1 / 20

Apogee Caliper Instructions Manual Download Page 1

Instructions for exchange of the bass slides in a APOGEE
CALIPER, DUETTA

Caveat

:

The exchange of a bass slide is not for the inexperienced handyman. Some

skills, technical understanding and experience in working with tools is
Prerequisite for the success of the exchange.

We take no responsibility for damaged or crumpled foil and poor
sound results after installation.
With careful work, and sufficient technical expertise is the result of
compared to the original.

What do you need

?

Tool

: Hammer

a good bit set with Zollbits

Elektrotacker

Superglue
double-sided tape

Screwdriver

Silicone
Velcro strips

  5 pcs 5mm spacers (wood)
  Punch 8 mm
  a 2-meter table

Cutting knife

Measurement

: Multimeter

Microphone
Audio software for frequency measurement

Preparation

Make sure you order the correct film. We supply the left and right
separately.
In addition, the films for the signature/reference models are not the same as the
standard models.
Check the contents of the delivery.

Included:

1 Bass Panel

1 set of damping strips
1 tube Aluminiumlot

1 Manual-CD

soldering iron

scrapers

1
2
3
...
»

Summary of Contents for Caliper





















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands