API A790 Operation Manual Download Page 16

Page: 16 / 138

Getting Started

1-6

Taking a Look at the Computer

This section identifies the external components of the computer and
briefly describes the function of each component.

NOTE

: Depending on the model you purchased, the appearance of your computer may

not exactly be the same as those shown in this manual.

Right-Side Components

Ref

Component

Description

See Also

PC Card Slot

Accepts a PC card for additional functions.

P. 4-9

Bay1 Slot

May contain a floppy disk / optical / secondary
hard drive / secondary battery module.

Audio Output
Connector

Connects a set of headphones, external speakers
with amplifier, or an audio recording device.

P. 2-21

Microphone
Connector

Connects an external microphone.

P. 2-21

IEEE 1394B Port

Connects a 1394B device such as a mass storage
device, digital video (DV) camcorder, or a
digital audio device.

P. 4-8

Hard Disk Drive
Compartment

Contains the hard disk drive of your computer.

P. 2-14

Summary of Contents for A790











































































































































Search results

Summary of Contents for A790

Reviews:

Brands by name

Popular brands

API A790, Operation Manual

Search results

Summary of Contents for A790

Reviews:

Brands by name

Popular brands