Apex Digital MASS FLOW METER Operating Manual Download Page 21

Page: 21 / 46

2020.07.24

•

REV. 2

• MASS FLOW METER OPERATING MANUAL

Device Info

If you run into trouble using your flow meter,

the

ABOUT

menu contains information that can

make the troubleshooting process easier.

Select

MFG INFO

to look up the manufacturer

phone number and web address.

DEVICE

INFO

shows you the serial number and firm-

ware version (

SW:

) for your specific device.

It also gives you the original manufacturing

date and the last calibration date, as well as

the initials of the calibration technician.

✓

Note:

The MFG INFO screen

can be used to find contact

information to troubleshoot

or configure the device.

Menu

→

About

•

DEVICE INFO

, displays serial

number, firmware revision, and

calibration information.

•

DEVICE STATE

displays diagnostic

information for troubleshooting (below).

•

MFG INFO

displays contact information.

•

BACK

returns to the top-level

menu (

page 20

•

MAIN

exits to the Main

Display (

page 17

Menu

→

About

→

Device State

Diagnostic Information

The

DEVICE STATE

screen displays live

values for the internal device registers. Many

of these values can help an applications

engineer diagnose operational issues over

the phone. Some register values clearly

distinguish between hardware and oper-

ational problems, which speeds up the

troubleshooting process.
Within the

DEVICE STATE

screen, press

PAGE

to advance to the next page of register values.

DEVICE DEVICE

MFG

INFO

STATE

INFO

BACK

MAIN

The About Screen

MODEL:

M-1SLPM-D

SERIAL NO:

123456

DATE MFG:

05/25/2020

DATE CAL:

05/25/2020

CAL BY:

SW:

8v13.0-R23

BACK

MAIN

Device Info Screen

PAGE

R8: AP Sig

15178

R9: Temp Sig

39089

R10: DP Sig

9869

R11: DP Brdg

40484

R12: Vlv Drv

R13: AP Brdg

40484

R16: MeterFunc

199

BACK

EDIT

MAIN

Device State Screen

Summary of Contents for MASS FLOW METER















































Search results

Summary of Contents for MASS FLOW METER

Reviews:

Related manuals for MASS FLOW METER

Brands by name

Popular brands

Apex Digital MASS FLOW METER, Operating Manual

Search results

Summary of Contents for MASS FLOW METER

Reviews:

Related manuals for MASS FLOW METER

Brands by name

Popular brands