background image

Instruction manual

CM20DTS / CM30DTD / CM60DTD

5

personnel.

•   Use cables of the right gauge, especially for long runs or high 

power systems.

•   Use cables with clear colour indication and maintain polarity 

throughout the whole system.

•   Avoid loud feedback from microphones; this can damage your 

loudspeaker.

•  Clean only with dry cloth.

•   Avoid touching the unit’s sharp metal edge to prevent injury.

•   Do not block any ventilation openings. Install in accordance 

with the manufacturer’s instructions.

•   Only use attachments/accessories that are specified and 

approved by the manufacturer.

•   Install the loudspeaker in a location that can structurally 

support the weight of the unit and its mounting hardware.

•   Tighten all speaker clamps securely. Doing otherwise may result 

in the unit falling down and causing personal injury and/or 
property damage.

•   Do not hold the tweeter as a handle to carry the unit; this can 

damage your loudspeaker.

•   Always attach a safety cable to both seismic safety tabs to 

secure the loudspeaker to the building structure. Please, be 
guided by applicable building codes here. Otherwise the unit 
could fall down, resulting in personal injury or even death.

•   Use only industry-accepted mounting tools and methods.

Summary of Contents for CM20DTS





























Reviews: