background image

Antona Corporation   (818)783-4299 http://www.antona.com

1

Antona  Corporation

Copyright

Copyright 

2000 Antona Corporation.  All rights reserved.  No part of this

publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, except within
the bounds of normal internet activity from the antona.com website, without the prior
written permission of the Antona Corporation of Los Angeles, California.

Warranty

Antona Corporation products are warranted to be free from defects in materials

and workmanship for a period of one (1) year from the date of original shipment to
customer.

This warranty is limited to the replacement or repair of parts not subjected to

misuse, neglect, unauthorized repair, alteration (except card options), accident, or
failure due to the effects of static electricity discharge.

In no event shall Antona Corporation be liable to the purchaser for loss of use,

profit, or consequential damages, or damages of any kind, including, but not limited to,
accidental loss or damage to other equipment, arising out of use of Antona Corporation
equipment, whether or not said equipment was used properly.  The designer is
responsible for the determining the suitability and use of the product.

This warranty is in lieu of any other warranty, expressed, implied, or statutory,

including, without limitation, any implied warranty or merchantibility or fitness for a
particular purpose. No amendment of this warranty may be effected except in writing by
an officer of the Antona Corporation.

All repair services shall be performed at the Antona Corporation plant in

Los Angeles, Ca.  

THE PURCHASER MUST OBTAIN A RETURN

AUTHORIZATION FROM THE ANTONA CORPORATION PRIOR TO
RETURNING ANY PIECE OF EQUIPMENT

.  Shipment to the Antona

Corporation will be at the expense of the purchaser, return shipment will be at the
expense of the Antona Corporation for all warranty repairs.

Summary of Contents for ANC-7020 Series












Reviews: