Anton Paar DMA 4100 M Instruction Manual Download Page 124

Page: 124 / 152

Appendix D: Adjusting the Camera Settings

124

C76IB003EN-E

Appendix D: Adjusting the Camera

Settings

D.1

Adjusting the Camera Position

If the camera does not show the complete measuring cell, you can adjust the

position of the camera.

1. Log on as "administrator".

2. Tap the

button in the quick access area.

The camera window opens.

Fig. D - 1

Adjusting the camera position

3. Use the position buttons to accommodate the position of the camera.

4. To save the current camera position, tap <Save Position>.

5. Close the camera window by tapping <X>.

D.2

Setting the Camera Illumination

If the illumination of the camera picture is not suitable for your special

environment, you can change the corresponding default setting.

1. Log on as "administrator".

2. Tap <Menu> and select

"Setup > Control Panel > Advanced Camera

Settings"

3. Increase the value "Auto Exposure Luminance" to increase the brightness of

the camera picture.

Position
buttons

Summary of Contents for DMA 4100 M

























































































































































Search results

Summary of Contents for DMA 4100 M

Reviews:

Related manuals for DMA 4100 M

Brands by name

Popular brands

Anton Paar DMA 4100 M, Instruction Manual

Search results

Summary of Contents for DMA 4100 M

Reviews:

Related manuals for DMA 4100 M

Brands by name

Popular brands