ANTAIRA LNX-1204G-SFP Series User Manual Download Page 6 | Manualshive

Page: 6 / 23

background image

Antaira Technologies - Industrial Ethernet Switches

LNX-1204G-SFP Series User Manual V1.1

2

1.2 Package Contents



1 - LNX-1204G-SFP (T): 12-port industrial gigabit unmanaged Ethernet switch, with

8*10/100/ 4*100/1000 SFP slots



1 - User manual



1 - Product CD



2 - Wall mounting brackets and screws



1 - DC cable –18 AWG & DC jack 5.5x2.1mm

1.3 Safety Precaution

Attention:

If the DC voltage is supplied by an external circuit, please use a protection

device on the power supply input. The industrial Ethernet switch’s

hardware specs, ports, cabling information, and wiring installation will be

described within this user manual.

«
...
4
5
6
7
8
...
»

Summary of Contents for LNX-1204G-SFP Series
























Reviews:

No comments

Related manuals for LNX-1204G-SFP Series

Switch 4500 Family

Brand: 3Com Pages: 742

Brand: 3Com Pages: 940

Brand: 3Com Pages: 43

OfficeConnect WX1200

Brand: 3Com Pages: 646

Brand: Patton electronics Pages: 104

Brand: Broadcast Tools Pages: 28

Brand: Teseq Pages: 60

Brand: Server Technology Pages: 12

Brand: Dahua Pages: 17

Brand: H3C Pages: 10

Brand: Maiwe Pages: 5

Brand: Comprehensive Pages: 12

R-TEC Automation RTMWSR15C

Brand: Rowley Pages: 10

Brand: Hubner Pages: 23

TM-1-8290/E/SVB

Brand: Eaton Pages: 2

Brand: Penguin Computing Pages: 71

Brand: HighSecLabs Pages: 10

Brand: Generac Power Systems Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands