ANTAIRA LMP-1600G-M12-67-110 Series Hardware Manual Download Page 3

Antaira Technologies - Industrial Ethernet Switches

LMP-1600G-M12-67-110 Series - Hardware Manual - v1.0

Caution:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority

to operate the equipment.

Avertissement FCC

Cet équipement a été testé et déclaré conforme aux limites d'un appareil numérique de classe A, conformément à la

partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences

nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l'énergie radiofréquence.

Cela peut provoquer des interférences nuisibles aux communications radio si l'équipement n'est pas installé et utilisé

conformément aux instructions. Cependant, il n'y a aucune garantie qu'aucune interférence ne se produira dans une

installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou télévision, ce qui

peut être déterminé en éteignant puis en rallumant l'équipement, l'utilisateur est encouragé à essayer de corriger les

interférences par une ou plusieurs des mesures suivantes:

Réorientez ou déplacez l'antenne de réception.

Augmentez la distance entre l'équipement et le récepteur.

Connectez l'équipement à une prise sur un circuit différent de celui auquel le récepteur est connecté.

Consultez le revendeur ou un technicien radio / TV expérimenté pour obtenir de l'aide.

CE Mark Warning

This is a Class-A product. In a domestic environment, this product may cause radio interference in which case the user

may be required to take adequate measures.

Avertissement de marque CE

Ceci est un produit de classe A. Dans un environnement domestique, ce produit peut provoquer des interférences radio,

auquel cas l'utilisateur peut être amené à prendre des mesures adéquates.

Industrial Ethernet Switches

Industrial Grade Managed Ethernet Switches

Hardware Manual

Version 1.0 (December 2021)

The manual supports the following models:

LMP-1600G-M12-67-110

LMP-1600G-M12-67-110-T

Summary of Contents for LMP-1600G-M12-67-110 Series


























Reviews: