ANTAIRA LMP-1202M-SFP Hardware Manual Download Page 6

vi 

Antaira Technologies - Industrial Ethernet Switches 

LMP-1202M-SFP Series Hardware Manual V1.0 

 

 

1. Introduction 

All Antaira industrial managed switches come with a pre-installed “user friendly” web console interface, 
which allows users to easily configure and manage the units, whether one is using a serial console and 
command line interface(CLI) commands like Telnet, SSH, HTTP (Web GUI) or simple network 
management protocols (SNMP). 

 

1.1 Product Overview 

Antaira’s LMP-1202M-SFP series 

is a 12-port industrial PoE+ managed Ethernet switch that is 

embedded with 8*10/100Tx Ethernet ports that support IEEE802.3at/af for a maximum of 
30W/port, 2*10/100/1000Tx RJ45 and 2*100/1000 dual rate SFP slots for Gigabit fiber 
connections. The LMP-1202M-SFP series is a fully manageable Layer 2 Ethernet switch that is 
pre-loaded with a user-friendly web management console design. It supports the ring network 
redundancy function using the market’s open standard ITU-T G.8032 ERPS (Ethernet Ring 
Protection Switch) protocol that has a <50ms network recovery time. The advanced network 
filtering and security functions, such as, IGMP, VLAN, QoS, SNMP, RMON, ModbusTCP, and 
802.1X/HTTPS/SSH/SSL increase determinism and improve network management for remote 
SCADA systems or control networks. 

 

The LMP-1202M-SFP series is IP30 rated and DIN-rail mountable. There are also two wide 
operating temperature models for either a standard temperature range (STD: -10°C to 70°C) or an 
extended temperature range (EOT: -40°C to 75°C). It also provides high EFT and ESD protection 
for industrial networking applications, such as, power/utility, water wastewater, oil/gas/mining, 
factory automation, security surveillance within transportation, ITS and any other outdoor or harsh 
environment. 

 

1.2 Product Software Features 

 

Network Redundancy

 

  STP, RSTP, MSTP, ITU-T G.8032 Ethernet Ring Protection Switch (ERPS) for network 

redundancy 

 

Network Management

 

  Web UI based management, SNMP v1/v2/v3, Serial Console 

  Qos, traffic classification QoS, Cos, bandwidth control for Ingress and Egress, 

broadcast 

storm control, Diffserv

 

  IEEE802.1q VLAN tagging, port-based VLAN support 

  IGMP snooping v1/v2, IGMP filtering / throttling, IGMP query up to 256 group 

Summary of Contents for LMP-1202M-SFP























Reviews: