Antaira Technologies
ARS-7235-5E-AC Series
Industrial 5-Port Gigabit Ethernet with Dual Radio IEEE
802.11a/b/g/n/ac Wireless Access
Point/Client/Bridge/Repeater/Router
Quick Installation Guide
Version 1.0
(December 2021)
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
19020000000136
Package Check List
The package contains the following items:
Quick installation guide
ARS-7235-5E-AC(-T)
Wall mounting bracket set with screws
Set of antennas
Front Panel Layout
Top Panel View
ARS-7235-5E-AC series top panel is equipped with one 6-pin
removal terminal block connector for dual DC power inputs
(9~48VDC).
Product Overview
System Interface/Performance
All RJ45 ports support the auto MDI/MDI-X function
Embedded 5*10/100/1000Tx RJ45 ports
Qualcomm IPQ4029 SoC
WLAN supports 2.4G/5GHz Wi-Fi
Power Input & Connection
DC 9 to 48V redundant power, with a 6-pin removal terminal
block
It is recommended to use a UL listed industrial power supply
Operating Temperature
Standard operating temperature model: -10°C to 60°C
Extended operating temperature model: -35°C to 70°C
Case/Installation
IP30 protection
DIN-Rail and wall mount design
LED Indicators
LED
Color
Description
Power 1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
Power 2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 is inactive
Off
Preconfigured alarms are detecting failure
Wi-Fi Signal
Strength
Green/Red
Red
Less than 25% signal strength
Green
LED 2 less than 50% signal strength
Green
LED 3 less than 75% signal strength
Green
LED 4 less than 100% signal strength
Diagnostics
Red
Flashing
Unit not ready / Boot sequence
Off
Unit ready
ETH Port 0~4
(Upper LED)
Amber
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
ETH Port 0~4
(Lower LED)
Green
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDI-X)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or
1000Base-T device connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
Pins
T568A Color
T568B Color
10Base-T,
100Base-TX
1000
Base-T(X)
Pin 1
white/green stripe
white/orange stripe
Rx+
TP0+
Pin 2
green solid
orange solid
Rx-
TP0-
Pin 3
white/orange stripe
white/green stripe
Tx+
TP1+
Pin 4
blue solid
blue solid
unused
TP2+
Pin 5
white/blue stripe
white/blue stripe
unused
TP2-
Pin 6
orange solid
green solid
Tx-
TP1-
Pin 7
white/brown stripe
white/brown stripe
unused
TP3+
Pin 8
brown solid
brown solid
unused
TP3-
Power Input Wiring
Please follow the steps below to insert the power wire:
1. Insert the positive and negative wires into the
PWR1
(V1+, V1-)
and
PWR2 (V2+, V2-)
contacts on the
terminal block connector as shown below in
Figure 1
.
Reset Button
LED for Power 1, Power 2, and Fault
Grounding Screw
6-Pin Removal Terminal Block (Power Input)
Antenna
LED for Wireless Strength
ETH# 0~4 – 10/100/1000Tx RJ45
LED for Diagnostics
LED for Activity Status - 10/100Mbps
LED for Activity Status -
1000Mbps
Antenna