manualshive.com logo in svg

Anritsu Company Site Master S312D, Maintenance Manual, Page: 9 / 62

Share
Download
Anritsu Company Site Master S312D Maintenance Manual Download Page 9

General Information

1-4

Replaceable Parts

S312D MM

PN: 10580-00195 Revision B

1-3

1-4

Replaceable Parts 

Important Information Regarding Service of Anritsu Equipment

Only qualified service personnel should attempt to perform repairs on this instrument. During the warranty 
period, opening of the case by non-Anritsu Service personnel will void the warranty.
Extreme care must be used when handling internal assemblies. Careless handling will cause damage.
Unless authorized by the factory, no attempts should be made to repair a defective assembly. (Discharged RTC 
batteries on the main PCB may be replaced). Exchange assemblies that are determined to have been damaged 
by improper handling will not be accepted for credit.

Table 1-2.

List of Replaceable Assemblies

Part Number

Description

ND67965 S312D Main/SPA Assembly (without Option 10A, without Option 31)

ND67967 S312D Main/SPA Assembly (with Option 31, without Option 10A)

ND67969 S312D Main/SPA Assembly (with Option 10A, without Option 31)

ND67971 S312D Main/SPA Assembly (with both Option 31 and Option 10A)

ND66432 Option 5 PCB

3-633-26 Coin Battery for RTC

15-123 LCD Display

46649-6 Keypad Membrane

67199-3 Keypad PCB

633-27 Rechargeable battery

790-523 Speaker

48231-1 Battery Door

61440-1 Case Top

58214 Case Bottom

46655 Corner Bumper

40-168-R AC Adapter

Summary of Contents for Site Master S312D































































Reviews:

No comments